Applications 6

De la WikiLabs
Versiunea din 7 aprilie 2019 16:14, autor: Zhascsi (discuție | contribuții) (→‎Exercise 1)
(dif) ← Versiunea anterioară | Versiunea curentă (dif) | Versiunea următoare → (dif)
Jump to navigationJump to search

Exercise 1

D flip-flop

  • dff1 module with behavioral description of the D flip-flop
  • dff1_tb testbench with stimuli for d and clk

Dreg1.png

the output takes the value of the input, q <= d, but only at discrete moments of time, when the control signal clk changes from 0 to 1, always @(posedge clk).

Attention!

  • behavioral sequential descriptions use only always processes
  • any sequential variable is of reg type
  • all assignments for sequential variables are nonblocking assignments, i.e. they use the <= operator


clock generation in testbench

initial begin
    clk = 0;                 // initialization at time 0
    forever #10 clk = ~clk;  // toggle the clock at each 10 simulation steps
end

Attention!

  • the logic complementation operator is ~, which is different from the arithmetic minus operator -. If you wrongly assign clk = -clk, clk will stay forever at 0 because -0 = 0.


For the d input generate the following sequence in testbench:

Dffwave.png

See how the output q reacts or not to changes of the input d.

Attention!

  • the stimuli are generated in other initial processes, separate from the initial process that is used only for clock generation (which loops forever, and cannot go beyond the forever statement)
  • because the clock is continuously generated, the simulation doesn't stop by itself. It may be stopped from simulation menu buttons (the red stop button or the break button). A more practical approach (that restricts from the beginning the waveform to the area of interest) is to stop the simulation from the testbench through the $stop sistem task added with a convenient delay after the last stimulus change:
initial begin
    // code to generate various stimuli (data, control signals etc)
    #10 $stop;
end

Exercise 2

4 bit D register

  • reg4 module
  • reg4_tb testbench with stimuli for d and clk

The behavioral description is identical with that of the D flip-flop of Exercise 1 (the D flip-flop being nothing else than a 1 bit D register). However, the interface differs in terms of the widths for d input and q output.

Reg8.png

For the d input generate the following sequence in testbench:

Reg4wave.png


structural description with flip-flops

  • add dff1 file to this project
  • change the description of reg4 to a structural one, with 4 instances of dff1, connected as in the schematics below:
  • rerun the testbench

Reg4.png


Exercise 3

4 bit shift left register

  • shiftr4 module described structurally as in the schematics below. It is basically the reg4 module, but with the D flip-flops connected in a shift chain.
  • dff1 is added (copied) to this project
  • shiftr4_tb testbench with clk generation and a (random) bit sequence for si (serial input)

Shiftr4.png


reset

Almost always a sequential circuit needs to start from a valid configuration, usually the initial one (for example with all bits zero). Without a proper reset the shift register will start in a random configuration, and its outputs will be meaningless untill the first input bit is shifted till the rightmost position, which takes 4 clock cycles. In simulation the outputs will be undefined until the first input bit reaches them.

The reset is active for a short time after power up (at the beginning of the simulation). The active value may be 1 or 0.

Also, the reset may be synchronous or asynchronous. The synchronous reset takes effect only at the first active clock edge after the reset is applied (therefore, the syncronous reset pulse must last at least one clock cycle). The asynchronous reset has immediate effect.

Shiftr4rst.png

  • add to the dff1 module an input for rst, and change its description such that to react to a synchronous reset which is active low (when rst is 0)
  • add to the shiftr4 module an input for rst and connect it to the corresponding inputs of the dff1 instances
  • add a separate initial process in the testbench to generate a reset pulse as in the drawing:

Shiftr4rstwave.png

For any sequential process with reset (active 1 in the examples below) the template is:

  • for synchronous reset
always @(posedge clk) begin
    if(rst) begin
        // initialize sequential variables
    end
    else begin
        // sequential variables normal control
    end
end
  • for asynchronous reset
always @(posedge clk, posedge rst) begin // the reset signal appears in the sensitivity list, therefore the always process reacts immediately to it
    if(rst) begin
        // initialize sequential variables
    end
    else begin
        // sequential variables normal control
    end
end
  • change the dff1 description such that it reacts to an asynchronous reset which is active low, recompile, restart simulation and see how the output waveform is affected
  • shorten the length of the reset pulse, such that there is no any active clock edge during the reset as in the waveform below. Rerun and see that the asynchronous reset takes effect.
  • change back to the synchronous reset. Rerun and see that the reset pulse has no effect because no active clock edge catches it.
Shiftr4rstwave1.png

Attention!

  • the reset branch must be the first branch in the sequential always process (as in the templates above)
  • be sure that the reset active value is checked. if(rst) if it is active high (when 1), or if(~rst) if it is active low (when 0)


nonblocking versus blocking assignments

  • change the shiftr4 description to a behavioral one. Use a single always process to control all output bits individually
  • compare in simulation these two behavioral descriptions of the shiftr4 module:
  1. the correct description with nonblocking assignments
    q[3] <= si
    q[2] <= q[3]
    q[1] <= q[2]
    q[0] <= q[1]
  1. the wrong description with blocking assignments
    q[3]  = si
    q[2]  = q[3]
    q[1]  = q[2]
    q[0]  = q[1]


a simpler behavioral description

  • change the shiftr4 behavioral description such that all bits are shifted at once in a single statement that uses the concatenation operator:
q <= {si,q[3:1]} // the new value is the old value shifted one bit to the right and with si bit appended to its left