Diferență între revizuiri ale paginii „DIC Lab Work 5”

De la WikiLabs
Jump to navigationJump to search
Linia 12: Linia 12:
  
 
* It will describe in Verilog a 16x4b RAM with a read-write port. Reading is synchronous.
 
* It will describe in Verilog a 16x4b RAM with a read-write port. Reading is synchronous.
* The necessary debugging to connect will be written
+
* The necessary pin connections will be written
** Address to SW7-4 and date of entry to SW3-0.
+
** the address to SW7-4 and date of entry to SW3-0.
** writing activation signal at one of the buttons (KEY0 ... KEY3).
+
** the write enable signal at one of the buttons (KEY0 ... KEY3).
** Output memory at LEDR3-0.
+
** the output at LEDR3-0.
 
** memory clock input to one of the DE1 plate oscillators.
 
** memory clock input to one of the DE1 plate oscillators.
* Schedule the FPGA board, and using the switches and buttons on the board, write 3, 6, and 10 with the values ​​2, 1 and 7, then read them in the same order. Notice, using the LEDs of the board, if the memory has been stored.
+
* Program the FPGA, and using the switches and buttons on the board, write 3, 6, and 10 with the values ​​2, 1 and 7, then read them in the same order. Notice, using the LEDs of the board, if the memory has been written.
  
 
== Exercise ==
 
== Exercise ==

Versiunea de la data 30 mai 2018 09:34

Required Notions and Knowledge

Example

  • It will describe in Verilog a 16x4b RAM with a read-write port. Reading is synchronous.
  • The necessary pin connections will be written
    • the address to SW7-4 and date of entry to SW3-0.
    • the write enable signal at one of the buttons (KEY0 ... KEY3).
    • the output at LEDR3-0.
    • memory clock input to one of the DE1 plate oscillators.
  • Program the FPGA, and using the switches and buttons on the board, write 3, 6, and 10 with the values ​​2, 1 and 7, then read them in the same order. Notice, using the LEDs of the board, if the memory has been written.

Exercise

  • Describe in Verilog a 16x4b RAM with two ports:
    • A write-only sync port with the following signals:
      • WR_ADDR - the address you write
      • WR_EN - write command
      • WR_DATA - written data
    • A read-only read-only port with the following signals:
      • RD_ADDR - read address
      • RD_DATA - read data
  • The memory will be instantiated in the TOP module as shown below:

Cid lab6.jpg

module COUNTER (
    input clk,
    output reg [31: 0] cnt
);

always @ (posedge clk) cnt <= cnt + 1;

endmodule

module ROM(
    input [3: 0] in,
    output reg [3: 0] out
);

always @ (in)
    case (in)
        0: out=4'b1010;
        1: out=4'b0110;
        2: out=4'b0011;
        3: out=4'b1110;
        4: out=4'b1011;
        5: out=4'b1111;
        6: out=4'b0111;
        7: out=4'b1100;
        8: out=4'b0001;
        9: out=4'b0101;
        10: out=4'b1101;
        11: out=4'b0000;
        12: out=4'b0010;
        13: out=4'b0100;
        14: out=4'b1000;
        15: out=4'b1001;
    endcase

endmodule
  • Write the constraints required to connect the TOP module ports:
    • DIN to SW7-4,
    • ADR at SW3-0,
    • WEN la KEY3,
    • DOED to LEDR3-0,
    • clock input at CLOCK_50.
  • Schedule the FPGA board; Write the RAM with the values ​​required to produce DOUT a sequence of numbers indicated by the teacher.

Submission of Exercises

For scoring, the following files will be submitted to the e-mail address indicated by the teacher.

An archive zip

  • All Verilog files (with the .v extension) containing the circuit description
  • A constraint file with the .qsf extension
  • A Quartus project file with the .qpf extension

Note that the archive will only contain files (without directories).

The subject of the email message must follow the [Name] _ [First Name] _ [Group] _Mem example Popescu_Ion_423B_Mem